Weld, Baby, Weld!

I finally made it to the metal shop on Monday.  As expected, once I had material in hand, I started to make quick progress.  Repairs to the passenger side wheel wells and fire wall have been completed, the rear passenger structural tube and passenger jack point restored, passenger floor pan reinforced, and the passenger door body mount re-fabricated.

(front wheel well:  prepped)

(front wheel well:  after)

(rear wheel well:  before)

(rear wheel well:  after)

(rear wheel well:  before)

(rear wheel well:  prepped)

(rear wheel well:  after)

(passenger body mount)

(old)     -     (new)

(rear structural tube:  prepped - All the junk on the floor was packed in the little structural channel above.  The only opening to the space was a 1" diameter knockout.  I removed all the loose rust from the cavity and applied rust killer before closing it in again.

(after:  patched hole is at top, repaired jack point on rocker panel at bottom.)

(interior firewall:  before)

(interior firewall:  after)

(If the after photos look upside-down, it's because they are.  I now have the car bottoms-up to work on the rocker panels and trunk floor.  However, I thought it would be easier to compare results if the photos were in a similar orientation.)

I have also repaired the driver side trunk floor at the tow hook.  The damage here seems more probably due to improper towing or jacking rather than the collision event that damaged the front and driver sides of the vehicle.

(tow point:  before)

(tow point:  after)

I'm definitely not the world's best welder, but I'm improving.

For those of you that keep asking "did you prime it yet?  It's going to start rusting right away!" - I'm starting to get some light rust again in places (particularly where I've touched the car or otherwise left body moisture behind) but I have planned all along to rust proof and use rust-proof paint anyway.  This light surface rust won't be a problem, and until the welding/grinding is completed, I would just burn the primer off anyway.  In any case, at this rate it will only be another week before the new paint starts to go on!

Next up:  the trunk floor and rocker panels!

A nip here, and a tuck there

So now that the rusty bits are out of the way, the chassis resembles clean metal panels in most places and swiss cheese in the majority of others.

Because no one likes a cheesy car, my next task is to repair and/or replace the parts that most resemble lace or an old log ravished by termites.

Simply because it is the more accessible side at the moment, I am working around the car, clockwise, starting at the front passenger wheel well.  Areas addressed so far include:

1. Rust damage at fire wall / rocker panel area - expected damage type and area
2. Stress Fracture at stiffener brace - evidence of frame stress
3. Stripped out / dented brace connection point - repair needed for proper re-attachment of brace
4. Bent / Warped vent flaps - due to buckling of front corner
5. Bent / warped tow point area - due in part to improper jacking, but it turns out the worst damage is due to this whole corner being pushed back approx. 1/2" (presumably in a past wreck - this would be consistent with damage to the driver side fiberglass, radiator damage, and stress fracture (#2 above)).
6. Bowed out / disconnected panel - also due to the pushed-in corner.

1.  Rusted metal removed and prepped for patch work

2.  Cracked area welded shut

3.  Brace mount area re-shaped.  (I still need to weld a flat washer over the hole to restore the structural capacity.)
4.  Vent fins straightened / repositioned
5.  Bottom corner brace beat back into place and sheet metal flattened.
6.  Repositioning of the corner corrected most of the bow in the side panel.  Panel tack welded back into place along the length of the panel.

What at first looked to be mostly cosmetic repair turned out to largely require structural repairs to the main front channel frame.  As seen below, the bottom right corner is particularly buggered, and required beating back into place.

This is what it looks like after a lot of straightening. Note that although the worst damage was on the passenger side, it was enough force to tear the channel on the driver side, requiring a welding repair.

Procrastination, Paint, and Bare Metal

Howdy Stranger!

I'd love to make all kinds of excuses for my apparent lack of progress such as:

• I was practicing for and performing in two productions of Handel's Messiah with my son.

• I had to host at Easter
• I was helping my Dad put a roof on his house

• I had to visit my Grandparents
• I had to do field research and ride in my cousin's Sonett
• I put a ceiling on my back deck so I can barbecue in the rain

• It's been rainy and humid
• I've got a new big project at the office
• I had a campout with our Cub Scout den

But I won't.

Because, the fact is I'm just plain lazy.

And it'd all just be excuses and procrastination anyway.

Instead I'll catch you up to what few things I have managed to get accomplished since the last posting.

I got a few parts cleaned, 

rust treated,

and painted.  (At least the base coat)

I tried my hand at bending and double-flaring gas and brake lines, and reassembled the horns.

And I got some of the paint off the chassis.  

(That's my good buddy J in the background - without whom I wouldn't have gotten the job done - If I look p.o.'d, it's because he made me work all day.  I thought we were just going to sit in the back yard and drink beers!)

So there you have it - Proof that I'm a slacker. . .